- #Digi 003 pics of rear panel how to#
- #Digi 003 pics of rear panel driver#
- #Digi 003 pics of rear panel free#
Leave the rod in the pawl and take the lock pawl off the lock. Then, push the shaft toward the lock rod until they touch, then pull both the rod and screwdriver shaft out at the same time. Apply constant force on the rodĪnd alternate pinching the pawl clips until the rod pops out.Īnother trick, if you're having trouble releasing the rod from the pawl, is to use a screwdriver shaft about the same size as the lock rod and put the shaft into the lock pawl open end. Top or bottom tab on the pawl while applying force on the lock rod toward Next, remove the lock rod from the pawl (white plastic piece) OR remove the lock pawl from the lock and leave the rod in the pawl. There are a few differences between sides so we will try to show as much detail as possible.
#Digi 003 pics of rear panel driver#
Now you will have extra room to work inside the door.Īt this point in the tutorial, we will start showing more photos of the driver side door. Photo 12c shows pulling the lower channel out of the door. Photo 12b shows the clip on the top end of the lower channel after it has been disjoined from the upper channel. With bolt removed, pull lower channel straight down until the upper clip slides off the upper channel. Feel or look inside the door to see how the clip joins the two together before taking them apart. There is a clip on the top end that holds the lower channel to the upper channel. Photo 12a: Remove the bolt holding the lower window channel in place at the bottom of the channel. It only takes a minute and will give you allot more room to work.
#Digi 003 pics of rear panel free#
To free up additional work space inside the door, remove the lower window channel. This photo shows the lower window channel still in place. Try to peel the guard back carefully to keep as much If there is adhesive holding the splash guard in place, it is usually
![digi 003 pics of rear panel digi 003 pics of rear panel](https://cdn.shopify.com/s/files/1/0277/2631/5568/products/003R-PLUS-FACTORY_d1a577ed-8ecf-4570-a84e-1c774135f1f2_800x.jpg)
Gently peel back the splash guard to expose the opening to the door cavity. Once the panel is removed, take off the bar holding the splash guard You will need to disconnect theĬourtesy lamp wire before moving the panel more than a few inches.Ĭarefully disconnect the courtesy lamp before moving the door panel awayĬheck that no other wires are connected to the panel, then pull the panel With panel screws all removed, carefully lift the door panel up and awayįrom the door, but only a few inches. Look along theĮdge of the panel, there are several screws, especially along the bottom Shows removal of the screws holding the panel in place. Remove the bolt to the right on this photo. The next photo, #4 shows a close up of the bolt to remove. This is one of the screws or bolts holding the panel onto the Near the center of the photo you can see a bolt head in the switch moduleĬavity. Look for the release tab if the connectors This is held in place with some snap clips so carefullyĭisconnect the wires at the connector. Preparing to remove the electric window/door lock switch panel ahead Notice that the window is in the up position. Is snapped into place or held with a single screw so remove with care The first photo shows removal of the inner door handle shroud. Installation Procedure: (Special thanks to Unique Car Audio in Gilbert,ĪZ for use of their truck for this tutorial!)
![digi 003 pics of rear panel digi 003 pics of rear panel](https://s.sbito.it/images/d5/d5af97cb-d571-4e02-85ee-0c11ee833dc9.jpg)
Time Required: First door up to 45 min, second door about 30 min, depending Jimmi' Jammer® Part Number: 113200 (marked on back of package)Įach plate is marked 3200 Right (Passenger) or Left (Driver).
#Digi 003 pics of rear panel how to#
This tutorial will show you how to install a Jimmi' Jammer® onįull size Ford Expedition (97-02) or Lincoln Navigator (98-02). If you found this page searching for "Door Panel" information, you should take a moment to check out our Jimmi' Jammer® product here.
![digi 003 pics of rear panel digi 003 pics of rear panel](https://www.ixbt.com/dvd/infocus/in3104/rear.jpg)
Welcome to the on-line installation tutorial! Our Products